specsafe-verify

Run tests and validate implementation (CODE → QA stage). Loops back to dev if tests fail.

When to use:

• Implementation appears complete
• Need to validate against spec requirements
• Preparing for QA review
• Before marking spec as complete

Input: The spec ID (e.g., SPEC-20260211-001)

Steps

1. Validate CODE stage

   Check specs/active/<spec-id>.md:

   • Status must be CODE stage
   • Implementation files exist
   • Previous test run was passing

2. Run full test suite

   Execute all tests with coverage:

   bashCopy

   pnpm test --coverage  # or equivalent
   

3. Analyze results

   Check for:

   • ❌ FAILING TESTS: Loop back to dev
   • ⚠️ LOW COVERAGE: Flag for improvement
   • ✅ ALL PASSING: Proceed to validation

4. If tests FAIL → Loop to dev

   This is the critical feedback loop:

   Copy

   ┌─────────────┐     FAIL     ┌─────────────┐
   │   VERIFY    │──────────────│    DEV      │
   └─────────────┘              └─────────────┘
          │                            │
          │ PASS                       │ Code fix
          ▼                            ▼
   ┌─────────────┐              ┌─────────────┐
   │     QA      │              │  Re-test    │
   └─────────────┘              └─────────────┘
   

   Actions:

   • Show failing test names
   • Analyze failure patterns
   • Suggest fixes
   • Prompt: /specsafe:dev <id> to fix

   Do NOT proceed to QA with failing tests

5. If tests PASS → Validate against spec

   Cross-reference implementation with requirements:

   • ✅ All P0 requirements satisfied?
   • ✅ All scenarios covered?
   • ✅ Edge cases handled?
   • ✅ No unintended side effects?

6. Generate QA report

   Document validation results:

   markdownCopy

   ## QA Report: SPEC-YYYYMMDD-NNN
   
   ### Test Results
   - Total: 12
   - Passed: 12
   - Failed: 0
   - Coverage: 94%
   
   ### Requirements Validation
   - P0: 3/3 satisfied
   - P1: 3/3 satisfied
   - P2: 2/2 satisfied
   
   ### Recommendation: GO / NO-GO
   

7. Move to QA stage

   If validation passes:

   bashCopy

   specsafe qa "<spec-id>"
   

   This:

   • Updates spec status to QA
   • Archives QA report
   • Updates PROJECT_STATE.md

8. Show verification summary

   Display:

   • Test results (pass/fail counts)
   • Coverage percentage
   • Requirements satisfaction
   • QA recommendation
   • Next: /specsafe:done <id> or back to /specsafe:dev <id>

Output

If tests FAIL:

• ❌ Test failure report
• 📋 Analysis of failures
• 🔧 Suggested fixes
• 📋 Prompt: "Fix issues and run /specsafe:dev <id> again"

If tests PASS:

• ✅ All tests passing
• ✅ Coverage report
• ✅ QA validation complete
• ✅ Status: QA stage
• 📋 Prompt: "Ready to complete? Run /specsafe:done <id>"

Guardrails

• ⛔ NEVER proceed to QA with failing tests
• ⛔ NEVER override test failures
• Coverage target: minimum 80% (prefer 90%+)
• All P0 requirements must be satisfied
• QA report must be generated for traceability
• If NO-GO, document specific issues to fix

Example - FAIL

User: /specsafe:verify SPEC-20260211-004
→ Running tests...
→ ❌ 2 tests FAILED
→ Coverage: 87%
→ 
→ Failures:
→   - should reject invalid token
→   - should handle rate limiting
→ 
→ 📋 Run `/specsafe:dev SPEC-20260211-004` to fix

Example - PASS

User: /specsafe:verify SPEC-20260211-004
→ Running tests...
→ ✅ All 12 tests PASSED
→ ✅ Coverage: 94%
→ ✅ All P0 requirements satisfied
→ ✅ QA Report generated
→ Status: QA
→ Next: /specsafe:done SPEC-20260211-004